|
MSDS Eurepoxy
Resin Base |
|
Product Name: Eurepoxy TYPE 1 EUREPOXY BASE RESIN
Effective Date: 11/11/85 Date Report Printed: 11/11/85 |
INGREDIENTS
|
|
Renclion
products of epicholorohydrin 76-80% and bispheon a AlkyI
Glycidyl Ether 20-24%
Substances listed in the Ingredients Section are those identified
as being present at a concentration of 1% greater1 or 0.1% if the
substance on the list of potential carcinogens cited on OSHA Hazard
Communication Standard. When proprietary ingredient shows, the identity
of this substance may be made available as provided in 29 CFR 1910.1200(1).
|
PHYSICAL DATA
|
|
The
BOILING POINT: None.
VAP PRESS: Not applicable.
VAP DENSITY: Heavier than air.
SQL. IN WATER: None.
SP. GRAVITY: 1.12-1.14
APPEARANCE: Straw colored liquid.
ODOR: Mild aromatic odor.
|
FIRE AND EXPLOSION HAZARD DATA
|
|
FLASH
POINT: 245°F
METHOD USED: PMCC
FLAMMABLE LIMITS
LFL: Not determined.
UFL: Not determined.
EXTINGUISHING MEDIA: Foam, CO2, Dry Chemical
FIRE AND EXPLOSION HAZARDS: None.
FIRE-FIGHTING EQUIPMENT: None.
|
FIRE AND EXPLOSION HAZARD DATA
|
|
STABILITY:
(CONDITIONS TO AVOID) Excess heating over long periods
of time degrades the resin.
INCOMPATIBILITY: (SPECIFIC MATERIALS TO AVOID) Base.
HAZARDOUS DECOMPOSITION PRODUCTS: None under normal conditions.
HAZARDOUS POLYMERIZATION: Will not occur by itself but masses more
than 1 pound of product plus aliphatic amine will cause irreversible
polymerization with considerable heat buildup.
ENVIRONMENTAL AND DISPOSAL INFORMATION
ACTION TO TAKE FOR SPILL/LEAKS: Soak up in absorbent material or
scrape up. Residual can be removed with non-flammable solvent such
as methylene chloride.
DISPOSAL METHOD: Burn in adequate incinerator or bury in an approved
landfill.
|
HEALTH HAZARD DATA
|
|
STABILITY:
(CONDITIONS TO AVOID) Excess heating over long periods
of time degrades the resin.
INCOMPATIBILITY: (SPECIFIC MATERIALS TO AVOID) Base.
HAZARDOUS DECOMPOSITION PRODUCTS: None under normal conditions.
HAZARDOUS POLYMERIZATION: Will not occur by itself but masses more
than 1 pound of product plus aliphatic amine will cause irreversible
polymerization with considerable heat buildup.
|
ENVIRONMENTAL AND DISPOSAL INFORMATION
|
|
ACTION
TO TAKE FOR SPILL/LEAKS: Soak up in absorbent material
or scrape up. Residual can be removed with non-flammable
solvent such as methylene chloride.
DISPOSAL METHOD: Burn in adequate incinerator or bury in an approved
landfill.
EYE: Minor transient irritation. No corneal injury likely.
SKIN CONTACT: Only minor irritation may be skin sensitizer.
SKIN ABSORBTION: Not likely to be absorbed through skin in toxic
amounts
|
FIRST AID
|
|
EYES:
Irrigation of the eye immediately with water for five
minutes is good safety practice. Consult medical personnel.
SKIN: Contact will probably cause no more than irritation. Wash off
in flowing water or shower. Wash clothing before reuse.
INGESTION: Low in toxicity. Induce vomiting if large amounts are
ingested.
INHALATION: Remove to fresh air if effect occurs. Consult medical
personnel.
NOTE TO PHYSICIAN:
Eyes: Injury is unlikely. Stain for evidence of corneal injury.
Skin: May cause dermatitis. Known or suspect skin sensitizer.
Respiratory: Injury is unlikely.
Oral: Low in toxicity.
Systemic: Human effects not established. No specific antidote. Treatment
based on the sound judgment of the physician and the individual reactions
of the patients.
|
HANDLING PRECAUTIONS
|
|
VENTILATION:
Good room ventilation usually adequate for most operations.
RESPIRATORY PROTECTION: None normally needed.
SKIN PROTECTION: Clean body-covering clothing
EYE PROTECTION: Safety glasses without side shields.
|
ADDITIONAL INFORMATION
|
|
SPECIAL
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: Practice
good caution and personnel cleanliness to avoid skin
and eye contact Avoid breathing vapors of heated materials.
|
NFPA HAZARD RATING
|
|
4
= EXTREME HEALTH 1
3 = HIG
|
|
|
|
MSDS
HARDENER |
SECTION I
|
|
PRODUCT:
EUREPOXY TYPE 1 EPOXY HARDENER
PRODUCT CLASS: Epoxy Resin Hardener
DATE OF PREP: 07/01/89
PREVIOUS REVISION: 08/01/87
PRODUCT TYPE: Modified Allphatic Polyamine
D.O.I. Category: Corrosive Liquid N.O.S. UN 1760. Chemicals NOIBN
HAZARD RATINGS: Health (2) Fire (1) Reactivity (0)
|
SECTION II - HAZARDOUS INGREDIENTS
|
Diethylenetriamine(DETA)
C.A.S. NO. 111-40-0
ACGUI (ILV)
OSHA(PEL)
STEL
|
Less
than 15% by weight.
1 ppm; 4mg/M(3).
None established.
None established.
|
|
Tetraethylene
Pentamine(TEPA)
C.A.S. No. 112-57-2
ACGUI (ILV)
OSHA(PEL)
STEL
|
Less
than 3% by weight.
None established.
None established.
None established.
|
|
Modified
Allphatic Polyamine Chemical Identity
ACGUI (ILV)
OSHA(PEL)
STEL |
Greater
than 82% by weight.
Trade Secret
None established.
None established.
None established. |
SARA TITLE III Section 313: Not listed.
SUSPECTED CANCER AGENT: Yes ( ) NO (x)
|
|
|
|
